ADLER Lignovit Interior UV 100 Water-Based Wood Glaze | Professional Interior Wood Stain with UV Protection for Wall & Ceiling Elements (Mont Blanc)

ADLER Lignovit Interior UV 100 Water-Based Wood Glaze | Professional Interior Wood Stain with UV Protection for Wall & Ceiling Elements (Mont Blanc)

Professional-grade, water-based wood glaze with advanced UV absorbers for a lasting, natural matt finish on interior softwoods.

• Advanced UV Protection: Contains effective UV absorbers that stabilise wood lignin, significantly extending the natural appearance of softwoods like spruce and fir compared to standard colourless glazes.
• Rapid Project Turnaround: Dust-dry in just 30 minutes and sandable/recoatable in approximately 1 hour (at 23°C/50% RH), enabling faster completion of interior coating projects.
• Certified for Healthy Interiors: Meets stringent standards, including the Austrian Eco Label (UZ 01) and French A+ for very low VOC emissions, ensuring a healthier indoor climate for occupants.
• Optimised for Professional Application: Ready-to-use formula for spray or brush application, providing consistent 80-100 ml/m² coverage for predictable and efficient results on interior elements.

Achieve a Superior, Long-Lasting Finish for Interior Woodwork.

ADLER Lignovit Interior UV 100 is the professional’s choice for treating interior wall and ceiling elements. This water-based, thin-layer wood glaze is specifically formulated to enhance and protect softwoods, delivering a beautifully transparent and matt finish that preserves the natural character of the wood. Its high breathability contributes to a healthy and pleasant indoor climate, a key selling point for your clients.

Protect Your Work Against Yellowing.

The primary challenge with softwoods is their tendency to change colour over time due to UV exposure. Lignovit Interior UV 100 incorporates powerful UV absorbers that effectively stabilise the wood’s lignin. This provides much longer stabilisation of the wood’s natural appearance than conventional colourless glazes, ensuring your projects look pristine for years to come and reducing callbacks.

Engineered for Efficiency and Reliability.

Designed for industrial and trade use, this glaze offers excellent processing properties for spray or brush application. Its quick-drying formula streamlines your workflow, allowing for faster project completion and increased productivity. Trust ADLER for a reliable, consistent coating that meets the highest professional standards.

Technical Information

• Base: Water-based
• Application Methods: Cup gun, Brushing, Vacuum coater
• VOC Content: Max. 20 g/l (EU Limit Cat A/e: 130 g/l)
• Coverage: 80-100 ml/m² per application
• Drying Time (23°C, 50% RH): Dust-dry ~30 mins, Sandable ~1 hour, Fully dried ~12 hours
• Recommended Wood Moisture: 13% ± 2%
• Substrate: Softwoods (e.g., Spruce, Fir)
• Finish: Matt, Transparent
• Dilution: Water (0-10%)

Certifications

• ADLER green product
• Austrian Eco Label (UZ 01)
• declared product in baubook
• French ordinance DEVL1104875A: A+ (very low emission of volatile pollutants)

How-To Steps

1. Substrate Preparation: Ensure wood is dry (13% ± 2% moisture), clean, and free of grease, wax, or resin. Sand smooth surfaces with 120 grit sandpaper in the direction of the grain. Round off sharp edges.
2. Stirring: Stir the product thoroughly before use, avoiding the introduction of air bubbles.
3. Application: Apply one coat of Lignovit Interior UV 100 evenly using a cup gun, brush, or vacuum coater. Maintain a product, object, and room temperature of at least +10°C.
4. Drying: Allow to dry. The surface is sandable and recoatable after approx. 1 hour under optimal conditions (23°C, 50% RH).
5. Finishing: Apply a second coat if required. Clean the equipment immediately with water.

Recommendations

Particularly suitable for spruce and fir. Not suitable for coloured hardwoods like meranti and mahogany. For reclaimed or steamed wood, consider alternative products like ADLER Innenlasur (5309). Always perform a trial coat on the original substrate to verify the final colour and finish. For spray applications, use of a respirator (A2/P2) is recommended.